Expeditor
Expeditor is a Ruby library that provides asynchronous execution and fault tolerance for microservices.
It is inspired by Netflix/Hystrix.
Installation
Expeditor currently supports Ruby 2.1 and higher.
Add this line to your application's Gemfile:
gem 'expeditor'And then execute:
$ bundle
Or install it yourself as:
$ gem install expeditor
Usage
asynchronous execution
command1 = Expeditor::Command.new do
...
end
command2 = Expeditor::Command.new do
...
end
command1.start # non blocking
command2.start # non blocking
command1.get # wait until command1 execution is finished and get the result
command2.get # wait until command2 execution is finished and get the resultasynchronous execution with dependencies
command1 = Expeditor::Command.new do
...
end
command2 = Expeditor::Command.new do
...
end
command3 = Expeditor::Command.new(dependencies: [command1, command2]) do |val1, val2|
...
end
command3.start # command1 and command2 are started concurrently, execution of command3 is wait until command1 and command2 are finished.fallback
command = Expeditor::Command.new do
# something that may be failed
end
# use fallback value if command is failed
command_with_fallback = command.set_fallback do |e|
log(e)
default_value
end
command.start.get #=> error may be raised
command_with_fallback.start.get #=> default_value if command is failedIf you set false to Expeditor::Service#fallback_enabled, fallbacks do not occur. It is useful in test codes.
timeout
command = Expeditor::Command.new(timeout: 1) do
...
end
command.start
command.get #=> Timeout::Error is raised if execution is timed outretry
command = Expeditor::Command.new do
...
end
# the option is completely same as retryable gem
command.start_with_retry(
tries: 3,
sleep: 1,
on: [StandardError],
)using thread pool
Expeditor use concurrent-ruby's executors as thread pool.
require 'concurrent'
service = Expeditor::Service.new(
executor: Concurrent::ThreadPoolExecutor.new(
min_threads: 0,
max_threads: 5,
max_queue: 100,
)
)
command = Expeditor::Command.new(service: service) do
...
end
service.status
# => #<Expeditor::Status:0x007fdeeeb18468 @break=0, @dependency=0, @failure=0, @rejection=0, @success=0, @timeout=0>
service.reset_status! # reset status in the servicecircuit breaker
The circuit breaker needs a service metrics (success, failure, timeout, ...) to decide open the circuit or not. Expeditor's circuit breaker has a few configuration for how it collects service metrics and how it opens the circuit.
For service metrics, Expeditor collects them with the given time window. The metrics is gradually collected by breaking given time window into some peice of short time windows and resetting previous metrics when passing each short time window.
service = Expeditor::Service.new(
threshold: 0.5, # If the failure rate is more than or equal to threshold, the circuit will be opened.
sleep: 1, # If once the circuit is opened, the circuit is still open until sleep time seconds is passed even though failure rate is less than threshold.
non_break_count: 20, # If the total count of metrics is not more than non_break_count, the circuit is not opened even though failure rate is more than threshold.
period: 10, # Time window of collecting metrics (in seconds).
)
command = Expeditor::Command.new(service: service) do
...
endnon_break_count is used to ignore requests to the service which is not frequentlly requested. Configure this value considering your estimated "requests per period to the service".
For example, when period = 10 and non_break_count = 20 and the requests do not occur more than 20 per 10 seconds, the circuit never opens because Expeditor ignores that "small number of requests".
If you don't ignore the failures in that case, set non_break_count to smaller value than 20.
The default values are:
- threshold: 0.5
- sleep: 1
- non_break_count: 20
- period: 10
synchronous execution
Use current_thread option of #start, command executes synchronous on current thread.
command1 = Expeditor::Command.new do
...
end
command2 = Expeditor::Command.new do
...
end
command1.start(current_thread: true) # blocking
command2.start(current_thread: true) # blocking
command1.get
command2.getDevelopment
After checking out the repo, run bin/setup to install dependencies. Then, run bin/console for an interactive prompt that will allow you to experiment.
To install this gem onto your local machine, run bundle exec rake install. To release a new version, update the version number in version.rb, and then run bundle exec rake release to create a git tag for the version, push git commits and tags, and push the .gem file to rubygems.org.
Contributing
- Fork it ( https://github.com/cookpad/expeditor/fork )
- Create your feature branch (
git checkout -b my-new-feature) - Commit your changes (
git commit -am 'Add some feature') - Push to the branch (
git push origin my-new-feature) - Create a new Pull Request